Here are some tips on handling problems and LaserJet printer toner cartridges:
1. Paper Jams (paper sandwiched)
Paper is damp or not feasible to cause paper jams or pinched, the printer engine is dirty by the dust on paper sometimes can also cause the paper jammed. If paper jams occur on your printer, open the printer cover and try to remove a jammed paper by pulling out the direction of discharge papers. Clean and wipe the surface of the rollers or roller conveyor and the sides of the machine using a soft cloth. Installation of paper rollers, hooks paper, gears, and sensors that are less precise and can cause paper pinned to this case required a technician who understands about troubleshooting the printer. When you try to remove paper that is stuck try to always issue a paper discharge direction of the paper.
2. Paper prints wrinkled / wrinkle / Clubs
Hook on the rollers of paper that is outdated / worn can cause wrinkled paper printouts. The paper size is not in accordance with the installation of sensor limits printer can also cause paper to wrinkle. Paper is damp or not dried properly can also produce the wrinkling. Try to adjust the paper size with hook-path rollers and try to use paper that is smooth and clean.
3. The lines on the print sheet
If there is paper printed page black stripes, this is because of several causes, this is usually due to the presence of foreign objects attached to the scanner or reflective glass. If problems are not on the glass reflector can be located at the imaging unit. If you have another cartridge (more than one) is recommended you replace the cartridge with the others that if good. This can overcome the above problems. If the printer uses a multi-component system (drum, toner, developer, each separate unit), this makes the problem more complicated. But surely there are such problems. Toner is usually no problem. If there are big black lines / width on the printed page, usually caused by a drum that is worn or weak, and need to be replaced with a new drum to resolve the issue.
4. Black dots on the page
If there are lines of black dots like a sprinkling of toner on a print sheet, a problem usually found in units of the developer cartridge. And usually it is difficult to be corrected except by replacing it with a new developer concerned. If the black dot sequence is repeated or there are down on the print sheet, there is usually a defect or an object attached to the drum unit. Rub with a soft cloth to remove foreign objects attached to or to replace the drum if there is a small hole on the surface of the drum. But this problem can also be found on the printer sensor is dirty and if so it must be serviced at once if possible.
5. Print sheet blank / does not mean
If there are bright lines or empty area / blurry on printout, this is caused by the toner is depleted or not blend in perfectly. Make sure you have enough toner powder in a cartridge that can reach the drum. Another problem may be caused by the fact that the drum surface can not touch the toner because wiper blade filter unit, dr. blade worn / hard. This means you must replace the relevant components. Often the problem is not located on the machine or cartridges, but on paper. In this paper moist or contain oil so that the toner or ink can not stick perfectly to the paper. It’s usually such a bright spot blurring or smearing on the print sheet. If you are unsure, always use a clean, dry paper to see its result.
6. Double focus / imaging
The main cause of the double focus / imaging on a page is in the installation setting regulator / fuser assembly that is not appropriate. Combinations that do not fit between the drum and the toner can also be the cause. Rarely manufacturers that produce components that do not match the settings its fuse. Several types of printers sometimes do not run normally with interruptions application you use may be wrong in the use of ink that is causing the problem. Set interrupt your application to the printer through how many dots per inch (dots per inch) / dpi.
7. Transverse lines on the page
Place pulp or disposal of toner in the cartridge may be full. change and clean the landfills. Connection / inappropriate relationship between the imaging unit with the machine can also cause this. Clean relations / liaison with cloth or towel. Could be perfect toner cartridge is not installed on the printer or incorrectly installed drum. Or replace it with another cartridge and it will fix the problem.
8. Pages dark
Could be because the identity is set too thick, try to explain the focus / image. Some printers have the identity control of its own. Drum worn can be a problem and a bad quality toner can also be the cause. Some of the toner on the market have a thickness that is not good, therefore, try adjusting the identity desired. If still persists, please contact us. Your printer should be cleaned a total of dirt that is on the internal lenses, paper path, connections and reflector.
Paper is damp or not feasible to cause paper jams or pinched, the printer engine is dirty by the dust on paper sometimes can also cause the paper jammed. If paper jams occur on your printer, open the printer cover and try to remove a jammed paper by pulling out the direction of discharge papers. Clean and wipe the surface of the rollers or roller conveyor and the sides of the machine using a soft cloth. Installation of paper rollers, hooks paper, gears, and sensors that are less precise and can cause paper pinned to this case required a technician who understands about troubleshooting the printer. When you try to remove paper that is stuck try to always issue a paper discharge direction of the paper.
2. Paper prints wrinkled / wrinkle / Clubs
Hook on the rollers of paper that is outdated / worn can cause wrinkled paper printouts. The paper size is not in accordance with the installation of sensor limits printer can also cause paper to wrinkle. Paper is damp or not dried properly can also produce the wrinkling. Try to adjust the paper size with hook-path rollers and try to use paper that is smooth and clean.
3. The lines on the print sheet
If there is paper printed page black stripes, this is because of several causes, this is usually due to the presence of foreign objects attached to the scanner or reflective glass. If problems are not on the glass reflector can be located at the imaging unit. If you have another cartridge (more than one) is recommended you replace the cartridge with the others that if good. This can overcome the above problems. If the printer uses a multi-component system (drum, toner, developer, each separate unit), this makes the problem more complicated. But surely there are such problems. Toner is usually no problem. If there are big black lines / width on the printed page, usually caused by a drum that is worn or weak, and need to be replaced with a new drum to resolve the issue.
4. Black dots on the page
If there are lines of black dots like a sprinkling of toner on a print sheet, a problem usually found in units of the developer cartridge. And usually it is difficult to be corrected except by replacing it with a new developer concerned. If the black dot sequence is repeated or there are down on the print sheet, there is usually a defect or an object attached to the drum unit. Rub with a soft cloth to remove foreign objects attached to or to replace the drum if there is a small hole on the surface of the drum. But this problem can also be found on the printer sensor is dirty and if so it must be serviced at once if possible.
5. Print sheet blank / does not mean
If there are bright lines or empty area / blurry on printout, this is caused by the toner is depleted or not blend in perfectly. Make sure you have enough toner powder in a cartridge that can reach the drum. Another problem may be caused by the fact that the drum surface can not touch the toner because wiper blade filter unit, dr. blade worn / hard. This means you must replace the relevant components. Often the problem is not located on the machine or cartridges, but on paper. In this paper moist or contain oil so that the toner or ink can not stick perfectly to the paper. It’s usually such a bright spot blurring or smearing on the print sheet. If you are unsure, always use a clean, dry paper to see its result.
6. Double focus / imaging
The main cause of the double focus / imaging on a page is in the installation setting regulator / fuser assembly that is not appropriate. Combinations that do not fit between the drum and the toner can also be the cause. Rarely manufacturers that produce components that do not match the settings its fuse. Several types of printers sometimes do not run normally with interruptions application you use may be wrong in the use of ink that is causing the problem. Set interrupt your application to the printer through how many dots per inch (dots per inch) / dpi.
7. Transverse lines on the page
Place pulp or disposal of toner in the cartridge may be full. change and clean the landfills. Connection / inappropriate relationship between the imaging unit with the machine can also cause this. Clean relations / liaison with cloth or towel. Could be perfect toner cartridge is not installed on the printer or incorrectly installed drum. Or replace it with another cartridge and it will fix the problem.
8. Pages dark
Could be because the identity is set too thick, try to explain the focus / image. Some printers have the identity control of its own. Drum worn can be a problem and a bad quality toner can also be the cause. Some of the toner on the market have a thickness that is not good, therefore, try adjusting the identity desired. If still persists, please contact us. Your printer should be cleaned a total of dirt that is on the internal lenses, paper path, connections and reflector.
0 comments:
Post a Comment